Volume 6, Issue 5, September 2018, Page: 96-101
Study and Application of Hydraulic Jet Radial Drilling in Carbonate Reservoirs
Yan Jun, Center of Well Construction Engineering, Research Institute of Petroleum Exploration & Development CNPC, Beijing, China
Cui Mingyue, Center of Well Construction Engineering, Research Institute of Petroleum Exploration & Development CNPC, Beijing, China
He Anle, Center of Well Construction Engineering, Research Institute of Petroleum Exploration & Development CNPC, Beijing, China
Jiang Weidong, Center of Well Construction Engineering, Research Institute of Petroleum Exploration & Development CNPC, Beijing, China
Liang Chong, Center of Well Construction Engineering, Research Institute of Petroleum Exploration & Development CNPC, Beijing, China
Received: Jul. 31, 2018;       Accepted: Aug. 14, 2018;       Published: Sep. 12, 2018
DOI: 10.11648/j.ogce.20180605.13      View  417      Downloads  34
Abstract
The hydraulic jet radial drilling technology is a low-cost production and completion technology for effectively developing low-permeability marginal reservoirs, thin-bed reservoirs with edge and bottom water, and depleted oil and gas fields. It has been successfully and widely applied in sandstone, coalbed methane, and heavy oil reservoirs. In order to explore its application in carbonate reservoirs, specially economically and efficiently develop low-permeability thin-layer carbonate reservoirs, the pilot of hydraulic jet radial drilling technology in the carbonate reservoir application was successfully completed through the research on the principle, advantage, existing problems and application condition of radial jet drilling, economic productivity was got, and cost-effective development was achieved, this pilot provided a method for the development of low permeability thin layer carbonate reservoir. This research shows that the hydraulic jet radial drilling technology has its unique technical advantages, which can enable some reservoirs to increase production or injection, but it is not suitable for every well, it has certain applicable conditions, such as the depth, thickness, and temperature of the target zone, and the conditions of well inclination, casing and wellbore have certain requirements too. The hydraulic jet radial drilling technology can achieve the expected target based on the zone and well selection, in selecting layers, as far as possible, homogeneous oil layers with good reservoir physical properties should be selected; the key of its successful implementation is the depth and azimuth control, wellbore diameter and operation safety control. The application of hydraulic jet radial drilling in carbonate reservoirs will make the spray hose wear large due to its high Young's modulus the high hardness, which affects the treatment footage; the use of acid in jet drilling can increase the radial drilling footage, but on the other hand can also produce impurities affecting the operation. The working fluid for jetting must meet the requirements of no solid phase.
Keywords
Hydraulic Jet, Radial Drilling, Carbonate Reservoir, Technological Advantages, Technological Process
To cite this article
Yan Jun, Cui Mingyue, He Anle, Jiang Weidong, Liang Chong, Study and Application of Hydraulic Jet Radial Drilling in Carbonate Reservoirs, International Journal of Oil, Gas and Coal Engineering. Vol. 6, No. 5, 2018, pp. 96-101. doi: 10.11648/j.ogce.20180605.13
Copyright
Copyright © 2018 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
CHI Huanpeng, LI Gengsheng, HUANG Zhongwei, “Current Status and Analysis of Hydraulic Jet Radial Horizontal Well Technology”, DRILLING & PRODUCTION TECHNOLOGY, vol. 36 (4): 119-124, July 2013.
[2]
SHI Lianhai, LI Yonghe, GUO Hongfeng, “Radial Horizontal Drilling Techniques with High Pressure Water Jet”, PETROLEUM DRILLING TECHNIQUES, Vol. 29 (5):21-22, Oct. 2011.
[3]
BI Gang, MA Dongjun, LI Gengsheng, “Extension ability of hydra-jet sidetracking of radial horizontal well”, FAULT-BLOCK OIL & GAS FIELD, Vol. 23 (5):643-647, Sep. 2016.
[4]
Yan Chuanliang, Cheng Yuanfang, Deng Fucheng et al., Experimental study on the hydraulic fracturing of radial horizontal wells, ISRM-YSS-2017-079, 2017.
[5]
Ahmed H. Kamel. Radial jet drilling: A technical review. SPE-183740-MS, 2017.
[6]
W. Dickinson, R. Dickinson, A. Herrera et al. Slim hole multiple radials drilled with coiled tubing. SPE23639, 1992.
[7]
Marcelo Alberto Bruni, Jose Hugo Biasotti, Guillermo Danilo Salomone. Radial drilling in Argentina. SPE 107382, 2007.
[8]
P. Buset, M. Riiber, Arne Eek. Jet drilling tool: cost-effective lateral drilling technology for enhanced oil recovery. SPE 68504, 2001.
[9]
Bin Wang, Gensheng Li, Zhongwei Huang. Hydraulics Calculations and Field Application of Radial Jet Drilling. SPE-179729-PA, 2017.
[10]
MA Lailiang, WU Fucai, YANG Haibin, “Application of radial horizontal drilling technology in W5 well”, DRILLING & PRODUCTION TECHNOLOGY, vol. 28 (5): 17-22, Sep 2005.
[11]
XIAN Baoan, XIA Bairu, ZHANG Yi, “Technical analysis on radial horizontal well for development of coalbed methane of low coal rank”, COAL GEOLOGY & EXPLORATION, Vol. 38(4): 25-29, Aug, 2010.
[12]
ZHANG Shouren, HU Yanlin, LI Guichuan, “Short horizontal sectional radial drilling and fracturing technology of coalbed methane and application”, Coal Science and Technology, Vol. 44(5):50-53, May 2016.
[13]
LIANG Zhuang, GE Yong, LI Jie, “Application of waterpower injector radial horizontal well technology in CBM exploration”, Journal of Liaoning Technical University (Natural Science), Vol. 30 (3):349-352, Jun 2011.
[14]
CUI Longlian, WANG Haige, GE Yunhua, “New radial drilling technologies”, OIL DRILLING & PRODUCTION TECHNOLOGY, Vol. 30(6):29-34, Dec 2008.
[15]
HOU Shugang, LI Bangmin, ZHENG Weijian, “Study and application of ultra-short radius horizontal well technology in Zhongyuan oilfield”, DRILLING & PRODUCTION TECHNOLOGY, Vol. 36(3):24-28, May 2013.
Browse journals by subject